Home > How To > Burner & Reader On Same IDE Cable

Burner & Reader On Same IDE Cable

Contents

Finishing the IDE installation Double check all connections and make sure the device is set correctly as master or slave. What you propose is just not possible. Master should be selected if this will be the only device on a single IDE cable or if it is the second device to be connected and the other device is If you already have an optical drive installed then if possible leave a gap in-between it and the new drive. check over here

Transition Drive Uses Either Power Plug  (Gateway) Inspect your motherboard, too. Make sure that one device is jumpered as master, and one is jumpered as slave. If the other device is jumpered as Cable Select, then jumper the HP DVD/CD Writer drive as Cable Select. Just use the power plug you have, no worries. http://www.tomshardware.com/forum/261305-32-hard-drive-cable-drive

How To Connect Ide Dvd Drive To Sata Motherboard

Neither device on an IDE channel is detected after the HP DVD/CD Writer drive installation This may be a master/slave jumper problem. See your browser's documentation for specific instructions. {} Z7_3054ICK0KGTE30AQO5O3KA30U5 hp-support-head-portlet Actions ${title} Loading... Since there is no universal standard, each IDE device has its own configuration for these jumper pins.

Can I write to 3 devices simultaneously without any problems? My sources tell me that there was a loose standard to put the Master drive on the end of the 40-wire cable and the Slave in the middle but that was IGIG Tutorials 7.060 weergaven 6:33 ComputerTV How To: Convert an IDE Hard Drive to SATA - Duur: 5:57. Hard Drive And Dvd On Same Ide Cable These photos show the SATA data cable sockets on the motherboard, the red SATA data cable and its end plugs, and the black SATA power plug -- SATA Photos (Wikipedia)             The

Perhaps a solution is around the corner as there is a draft for a FireWire ATA interface. How To Connect Dvd Drive To Motherboard In order to use Cable Select jumpering, several conditions must be met. This can be checked with a voltmeter.

If both drives are set for CSEL and the host interface supports CSEL, but a regular cable is used, both drives will be seen as master.

made a huge difference.Long story short, spend 50$ get a seagate or Western digital 320 to 500gig drive. Ide To Sata Connector Additional computer CD-RW help and support. This can also be a problem with the physical location of the devices on the IDE cable. Cable Select is defined in the ATA-2 and ATA-3 specifications.

How To Connect Dvd Drive To Motherboard

Most motherboards have only PATA or SATA data connector sockets. http://www.osnews.com/story/25660/How_to_Integrate_SATA_and_IDE_Drives The data cable is labelled A and the power cable is labelled B. How To Connect Ide Dvd Drive To Sata Motherboard The devices should redetect after the jumpers are set correctly. How To Connect Dvd Drive To Motherboard Sata Please advise.

Is there a cable similar to IDE 1-2 cables for SATA interfaces this way I can use 6 DVD-writers instead of 3 and if so, will this have a performance impact check my blog The blue connector should be installed into the Primary IDE connector. If you have problems try treating them like a loose tooth, gently but firmly pulling while rocking the cable slightly from side-to-side. Just search on "IDE to SATA" at Amazon. How To Install Dvd Drive On Pc

The most foolproof way to see what type of drive your computer can take is to open it up and take a look at the drive or drives it's currently using. Not all sound cards will support more than one device at a time. Most of the time, but not always, you connect the 40-wire cable on the other Secondary connection. this content The power cable will be running from your power supply, locate it and plug it into the power socket on the device (see below).

Does clone CD work with SATA based interfaces and can write to the DVD-writers independently at the same time? 2. How To Connect Ide Hard Drive To Sata Motherboard Share the IDE channel with the hard drive Devices that are similar in access speed should share an IDE channel, whenever possible. This is not easily solved while achieving backward compatibility and will require cooperation between the major hardware manufacturers to make it work.

To edit the Config.sys file: (Microsoft(R) Windows 95, 98, NT, 2000 and XP) Click Start, and then click Run.

The final photo shows the back of an IDE disk drive. No problem installing on same cable as 1 hard drive. To determine what each vertical pair of pins represents on another IDE device, refer to the documentation that came with that device. Ide Hard Drive Jumper Settings Toevoegen aan Wil je hier later nog een keer naar kijken?

The letter assigned to the drive will depend on your machine's configuration. Sata is always better Is there a cable similar to IDE 1-2 cables for SATA interfacesClick to expand... The blue connector should be installed into the Primary IDE connector. have a peek at these guys Generally, if there are screws attaching the cover, they are on the back of the computer.

Ben bennaz, Jul 19, 2008 #3 bennaz Member Writing Multiple Images I have tried writing to two CD-Writers at the same time using the 1-2 IDE cable and using two Along one side of the cable is a stripe. PC Advisor Phones Smartphone reviews Best smartphones Smartphone tips Smartphone buying advice Smartphone deals Laptops Laptops reviews Laptops tips Best laptops Laptops buying advice Tablets Tablet reviews Best tablets Tablet tips Meer weergeven Laden...

advertisement To install your optical drive you will need: Compatible CD recorder or DVD drive (SATA or IDE). 4 securing screws (supplied with your CD recorder / DVD writer). I merged your duplicate thread into this one. Consult the computer user manual for information about changing IDE settings in the BIOS. expertvillage 67.449 weergaven 2:22 How to fix a broken hard drive Beeping noise or clicking RECOVER GET DATA BACK FOR FREE!

Reproductions must be properly credited. The Master was always the boot drive, the drive that contained the operating system. For Seniors: Contact Microsoft Customer Support Finding Large Files on Your PC Troubleshooting Your PC For Dummies, 3rd Edition Load more ComputersPCsHow to Install an Internal CD/DVD Drive in Your Computer It is not necessary to connect the audio cable to the HP DVD/CD Writer drive in order for it to be able to record audio CD’s.

This article discusses the options. Log in om dit toe te voegen aan de afspeellijst 'Later bekijken' Toevoegen aan Afspeellijsten laden... This position is used to ensure that the cable is attached to the drive in the correct position. Frequently Asked Questions: Can I connect a older ATA33 drive with my newer ATA66/100/133 drive?

Unfortunately some are flimsy or have poor quality control. If you have trouble removing the "blank" you can use a flat ended screwdriver to ease it out, taking care not to damage the case. Don't use junk blank media. All Rights Reserved.

Figure : Setting jumpers on the HP CD Writer Locate a drive slot Minimum system requirements for the HP DVD/CD Writers require an available 5.25-inch slot in the computer. Pictured here are the two cables, the 80-wire and the older 40-wire ATA IDE cables. IDE ribbon cables have either 40 or 80 wires.